Current position > Product detail
『Endress and Hauser Coriolis Flow Meter Review: Premium Mass Flow Measurement』Related information(v cone flow meter|rotary gas meter|gallon meter|gear meter|metal tube rotameter|glass tube rotameter|nutating disk meter|transit time ultrasonic flow meter|wedge flow meter|pd meters|hydraulic flow meter|ultrasonic water flow meter|water flow meter|air flow meter|magnetic water flow meter|oxygen flow meter|gas flow meter|argon flow meter|air velocity meter|gasoline flow meter|fuel flow meter|ultrasonic water meter|digital water meter|nitrogen flow meter|solid flow meter|Oxygen tank flow meter|digital water flow meter|diesel fuel flow meter|steam flow meter|02 flow meter|compressed air flow meter|oil flow meter|liquid flow meter)
Endress and Hauser Coriolis Flow Meter Review: Premium Mass Flow Measurement
Quick Answer: Endress+Hauser Promass Coriolis meters are a premium choice for direct mass flow, density, and temperature measurement in oil and gas, chemicals, and food processing. The instruments deliver lab-grade accuracy and handle demanding fluids from liquid ammonia to viscous resins. Many SMEs in Southeast Asia and the Middle East use them on critical control loops. But when process requirements are less extreme, a Silver Instruments Coriolis meter gives you close to the same performance without the heavy brand markup.
Promass Build Quality and Measured Variables
We often open Promass F and Promass A transmitters at customer sites. The tube design stands out. On an F 300 you see a fully welded 316L or Alloy C22 twin-tube setup with matched PT100 sensors embedded in the driver and pickoff points. The meter measures mass flow, fluid density, and temperature simultaneously on a single device. Accuracy on clean liquids can reach plus or minus 0.05 percent of rate with zero stability down to 0.01 kg/h on smaller DN15 sensors. Engineers in Singapore chemical plants use Promass I for aggressive media because the straight tube handles high viscosity up to 2000 cP without losing signal.
Electronics are another strong point. The transmitter runs multivariable outputs. Standard 4-20 mA HART, pulse, and Modbus RS485 come ready on the terminal block. ATEX Zone 1 and IECEx approvals are factory fitted on dedicated order codes. You can set up batching, net oil computing, or concentration measurement straight from the local display without a laptop. This saves commissioning time on a glycol injection skid in the Middle East.
Where the Premium Price Often Justifies Itself
There are applications where a Promass simply makes sense. Custody transfer of liquefied natural gas requires OIML R117 certification and traceable density uncertainty below 0.5 kg per cubic meter. E+H has the certified lines ready. A dairy plant in Australia using Promass Q for milk reception benefits from the EHEDG cleanability and 3-A authorization. These are hard to replicate with a generic Coriolis meter, and the documentation package alone can win an audit.
On a customer visit in Vietnam last year, a paint manufacturer running Promass I on solvent batching showed us five-year drift figures under 0.03 percent. The meters run 24 hours on toluene, MEK, and high-solid resins. No liner, no moving parts, no filter required upstream. This reliability avoids expensive batch rejection. When you measure resin by weight and the batch cost is high, the meter pays for itself in twelve months.
When Silver Instruments Coriolis Meters Become the Practical Alternative
Not every plant needs OIML or exotic Hastelloy wetted parts. A water treatment station dosing PAC coagulant at 15 bar and 25 degrees C needs repeatable mass flow, not metrological perfection. Here is where our SIL-Coriolis series makes sense. You get plus or minus 0.2 percent accuracy, 316L wetted parts, PT100 temperature output, and 4-20 mA HART with Modbus. Pipe sizes run from DN04 to DN150. The transmitter supports density-based concentration for caustic soda or sulfuric acid. Most engineers skip paying for the brand premium when the core measurement works the sam
We have seen this repeatedly on site. A lubricant oil blender in Nigeria replaced aging Promass F with Silver Instruments DN25 meters. The new meters fit the same flange spacing, talked Modbus to the PLC, and kept the blend ratio within 0.3 percent. The capital cost dropped by over 60 percent. Spare parts and support turnaround are faster because we ship small orders from regional stock.
Key Comparison Points on the Spec Sheet
When you put the two side by side, check these four parameters. First, look at mass flow accuracy at your minimum and maximum flow rate, not just the headline number. Zero stability matters for low flow. Second, note the wetted material list. Endress offers Alloy C22, titanium, and Tantalum for extreme acids. Silver Instruments standard line covers 316L, with Hastelloy C276 optional. Third, verify output protocols. Both brands deliver HART, Modbus, and pulse. For PROFIBUS or EtherNet/IP you need to specify the Promass variant; we keep options lean to avoid complexity. Fourth, confirm the explosion-proof certificate matches your zone. E+H carries ATEX, IECEx, and FM. Silver Instruments meters ship with ATEX II 2G Ex d ia IIC T6 Gb as standard; we can arrange IECEx on project orders.
FAQ
Q: Can Endress+Hauser Coriolis meters measure gas accurately?
Yes. Promass F and Promass A measure gas mass flow directly with uncertainty around plus or minus 0.5 percent of rate. They handle hydrogen, natural gas, and CO2. You do need sufficient density, so very low-density gases require careful sizing.
Q: What is the price range for a Promass F DN15?
List prices often start above 7000 USD for a basic compact version with 4-20 mA HART. Custom materials, high-temperature options, or custody transfer approvals push the quote higher. Actual pricing varies by region and project volume.
Q: How does Silver Instruments Coriolis accuracy compare?
Our standard accuracy is plus or minus 0.2 percent of rate on liquid mass flow and plus or minus 0.5 percent on gas. Density uncertainty is 0.002 g per cubic centimeter. For chemical batching or fuel measurement this is more than adequate.
Q: Can I get a spare transmitter without replacing the whole sensor?
Endress+Hauser sells standalone transmitters. Silver Instruments also supplies replacement transmitters compatible with our sensor types. Send us the meter serial number and we confirm fit.
Q: What outputs do I need to integrate with a Rockwell PLC?
If you use a ControlLogix system, Promass with EtherNet/IP option is a direct fit. With a Silver Instruments meter you commonly use Modbus TCP via gateway or a hardwired 4-20 mA and pulse. We can pre-configure the mapping before dispatch.
Get a Quote Based on Your Real Process Data
Instead of reading through generic brochures, send us your fluid name, flow range in kg per hour, pipe size in DN, operating pressure in bar, and temperature in degrees C. We will propose the correct Promass equivalent or a Silver Instruments alternative with a clear price comparison. Reach us at [email protected] or call +86-25-68650347. You can also text specifications via WhatsApp: +86-25-52155837 or WeChat: +86 15365082610. Our team answers technical queries within the same business day.